Over recent years, I’ve seen quite a few Roland MKS-80s and many have a broken data cartridge slot. At last, there’s a solution; my V06 Roland MKS-80 Broken Data Cartridge slot fix!
After more than three decades, the hard plastic from which the enclosure is made, has become very brittle and it doesn’t take much to break the screw pillars that secure the enclosure to the front metal chassis.
The data cartridge slot assembly comprises two halves. The back half has a female contact strip which mates with the male contract strip in the cartridge. It’s soldered to a small PCB. Long screws attach this section to the front half which has the flap.
The front half in turn, is secured to the metal front chassis via two M3 screws (one on top right and one at bottom left) that go through two small plastic flanges which are part of the front cartridge slot assembly.
The problem is that when inserting a data cartridge, you’re pushing the cartridge slot away from the front chassis and the small plastic flanges through which the screws pass that secure the front half of the slot assembly to the front panel, are stressed.
The most obvious fix is to use a type of cyanoacrylate (super-glue) or epoxy adhesive to repair the broken flanges. Only thing is, those flanges often break into several pieces. It’s a nightmare! If your data cartridge slot is intact, then you really (REALLY) want to avoid this ever happening.
Back in 1984, Roland should have designed the assembly such that it is properly supported from the rear.
Well, my V06 bracket continues where Roland left off and does just that! Designed to sit neatly on top of my Aurora Board B (or Board Bx), the V06 provides a physical resistance behind the data cartridge slot, thereby reducing the force on the front slot assembly screw flanges, the only things that are holding the whole data cartridge slot in place.
The very front of the data cartridge assembly, is designed such that it 'rests' on the MKS-80 front panel slot cut-out. This means that so long as there's something solid behind the assembly (like the V06), it's not going to move from side-to-side, let alone backwards and forwards.
If the data cartridge slot in your MKS-80 is just fine and you’re interested in Aurora, then you really should consider fitting the V06 bracket. Instead of relying solely on the enclosure’s two screws and the integrity of the screw flanges, the V06 will provide substantial protection against breakage.
The V06 bracket has a convenient cut-out which allows access to the voltage measuring pads for the Aurora Board Bx’s on-board Live Forever battery. That’s right, you don’t have to remove the V06 to check the battery voltage on the Aurora Board Bx! Hey, you don’t even have to remove the V06 if you need to ever change the Aurora Board Bx’s CR123! How cool is that?
I wish I thought of the V06 when I designed Aurora but all this stuff is kind of an evolutionary process. The Aurora Board Bx for example, didn’t happen until several months after Aurora was released. The two power supplies I’ve subsequently designed for other vintage synths however, both included my on-board Live Forever battery mod, from conception.
When I did come up with the idea of V06, I wanted something that could be retrofitted, a solution which existing Aurora customers could purchase and easily install themselves.
V06 is just so easy to fit:
- Just peel off the sticky tape protectors and attach the two rubber strips to the back of your data cartridge slot PCB (as shown below), in the two areas free of solder joints.
- Replace the four M3 nuts that secure Aurora Board B or Board Bx, with the 20mm M3 stand-offs supplied with the V06.
- With one hand, line up the data cartridge slot with the slot in the MKS-80 front panel and then with the other hand, slide the V06 plate on to the four stand-offs.
- Push the V06 plate forwards towards the data cartridge slot and use the M3 nuts you just removed, to secure the plate.
- Job done!
With just a M3 (5.5mm) nut-runner and no disconnecting of internal headers or soldering, once your MKS-80 is open, V06 can be installed in a couple of minutes.
So now, Aurora offers the following long-term solutions for the Roland MKS-80:
- Reliable, smooth, quiet power supply.
- Live Forever memory back-up battery.
- V06 Roland MKS-80 broken data cartridge slot fix.
Now that’s cool! 😀
- V06 can only be installed into a Roland MKS-80 that’s fitted with Aurora.
- V06 is supplied with all fixing hardware. All you need is a M3 (5.5mm) nut-runner.
If you have already bought Aurora and would like a V06, please just get in touch.
UPDATE - 4th May 2021
Back in the eighties, Jed Allen and I used to work together at Roland (UK), so imagine my surprise when he called asking if I could fit an Aurora into his MKS-80!
Jed's machine was in really good condition apart from the data cartridge slot which was very broken. In fact Jed told me that it had been bust for decades and that no one could fix it. Hmm... So while I was installing his Aurora, a little deep thought and I came up with the idea of the V06 bracket.
Jed kindly agreed to me keeping his machine for a few more days while I designed and had made the V06 (hey, what are friends for) and of course he became my very first V06 customer.
Apart from the pictures of the intact data cartridge slot assembly, all the other pictures are of Jed's MKS-80 and the V06 that went into it. And YES, that's Jed's Roland Juno-60 in the background, which I serviced at the same time. 🙂
If you already have an Aurora board fitted and would like to protect the data cartridge slot assembly in your MKS-80, you can buy V06 now...